![]() ![]()
M-Button : Quickly press and release sta. Special Features using the optional RC402N RC402N Features and Functions The remote control mirrors the basic functionality of the laser keypad and offers additional features using the M and E buttons. First, turn on the receiver, then press and hold the Deadband (A) and Audio (B) buttons for two seconds. Using the optional HL760 receiver To pair the HL760 receiver with the transmitter Make sure the transmitter is turned off. Check the laser beam elevation close to the laser. Set up the laser and align it to the desired slope hub using the sighting guides on the sunshade. Set up the laser and place the grade rod on. The HI is determined by adding the grade-rod reading to a benchmark or known elevation. Attach the laser onto the wall molding by sliding the wall mount over the wall.ĭetermining the Height of Instrument (HI) The height of instrument (HI) is the elevation of the laser’s beam. Inventek laser level user manual install#Determine and mark the finished ceiling height and securely install the first piece of wall molding to this height. Mask Mode can be selected as a standard fe.Īpplications Interior Acoustical Ceilings 1. Inventek laser level user manual manual#In Manual mode (ho.ġ2 Mask Mode Mask Mode – allows you to electronically turn off the rotating laser beam (electronic shutters) in up to 3 lighthouse windows to prevent interference with other receivers on the jobsite. Manual mode is indicated by the flashing (once every second) red LED e. Repeatedly pressing the Rotation button toggles through 0, 10, 80, 200, 600 rpm regardless if the unit is in automatic.ġ1 Standard Features Manual mode Pressing and releasing Manual button activates/deactivates the manual mode regardless if set up horizontal or vertical. The laser recognizes automatically whether it is used horizontally or vertically when swit.ġ0 Standard Features Rotation Mode Rotation speed can be selected using the Rotation button as well as using the RC402N menu. Laser Setup Position the laser horizontally (tripod mount and rubber feet downward!) on a stable platform, wall mount or tripod at the desired elevation. The LED will be on continuously when battery voltage is less than 3.8 volts. The LED will flash when battery voltage is between 3.8 and 4.0 volts. Recharging the Batteries Note: The battery LED shows the approximate charge of the batteries. Insert batteries (or a rechargeable battery pack) into the housing so that the negative poles are on the bigger battery spiral springs. Installing Batteries Remove the battery door by turning the center screw 90° counterclockwise. HV302 - Components 5 l q r j k m n o p q r a b c e d f g i hĬomponents a Power Button b Battery LED c Manual/Standby Button d Leveling LED e HI/Manual/Standby LED f Up and Down Arrow Buttons g Left and Right Arrow Buttons h Rotation Button i Scan Button j Rotor 6 k Sunshade l Sighting Gu. The HV302 laser is an easy-to-use tool that allows you to take accurate horizontal/vertical measurements, 90°- and plumb beam tra. Introduction Thank you for choosing one of the Spectra Precision Lasers from the Trimble family of precision lasers. Special Features using the optional RC402N RC402N Features and Functions Powering the RC402N Turning On/Off the RC402N Radio Remote Control Pairing the remote control with the transmitter MENU Features at the RC402N Rotation Scan Automa. ![]() Inventek laser level user manual how to#Well-suited for typical do-it-yourself projects, these laser levels are less expensive and require less battery power than a self-leveling unit.TABLE OF CONTENTS Introduction For Your Safety Components How to Use the Laser System Powering the Laser Turning On/Off the Laser Laser Setup Standard Features Rotation Mode Scan Mode Manual Mode Y-/X-Single Slope Mode Mask mode. Manual laser levels work in the traditional way: The user lines up a bubble inside a vial either by repositioning the level or turning a knob. Laser levels find "level" in different ways. The enclosure, or case, is usually made of a durable plastic or metal that's tough enough for sturdy performance on a job site. Inventek laser level user manual plus#There's also a leveling mechanism, either a bubble vial or a pendulum and magnets plus electronic sensors (the differences between these two types of mechanisms will be discussed below). This base helps you to project the light at the required height. Different types of laser levels have been developed for specific uses, but all laser levels include two common components: the laser plus a leveling base that can sit on the floor, mount on the wall or attach to a tripod. ![]() ![]() Laser levels are easy to use, and with a variety of designs available, there's a style that suits any application. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |